SILICONI | CLINOX GREEN - Stainless steel cleaner

MOLISIL is used as an anti-spatter product to protect the torch "nozzle" against droplet adhesion.
It is a very effective anti-spatter because it contains MOS2 and graphite in slightly higher quantities than a standard anti-spatter product
(oil-based).
MOLISIL can also be used as a lubricant to lubricate moving mechanical parts, prevent friction and reduce wear. It is used for high-temperature lubrication.

500 ml aerosol can

INSTRUCTIONS FOR USE

Clean and degrease the parts to be treated. Shake the aerosol vigorously until the ball moves, and during application, continue to shake the product occasionally to keep it homogeneous. Spray from a distance of 25 cm.
After use, invert the aerosol and spray the product for a few seconds to prevent valve clogging.

SPECIFICATIONS

Base: Molybdenum disulphide and graphite
Propellant: Odourless denatured hydrocarbon.
Temperature resistance: 700°C
Appearance: Dry grey film
CFC-FREE CHLORINE-FREE

SUPER CLEANER is a fast and powerful cleaner for removing: oils, greases, stains, dirt, and sludge. It is suitable for cleaning engines, gears, chains, hard surfaces, chrome parts, plastics, steel, bicycles, aluminium painted parts, chains, and gearboxes. It does not damage rubber, plastic, or carbon frames. Free from petroleum solvents. It contains additives that leave a shiny, protective film on treated surfaces. It does not corrode or scratch treated materials. BIODEGRADABLE.

Thanks to its formula, it can penetrate and dissolve all types of dirt or encrustation.

750 ml spray bottle

It cleans without leaving greasy residues.

Suitable for cleaning: industrial machines, workbenches, engines, chrome frames, chains, chrome parts, external engine parts, nozzles, mechanical movements, plates, iron parts, copper, engine parts, car rims.

SUPER CLEANER reduces the adhesion of dirt on treated surfaces.

✓ Non-flammable
✓ Non-toxic
✓ Ammonia-free
✓ Non-abrasive

INSTRUCTIONS FOR USE
Wet the parts to be cleaned with water, then apply SUPER CLEANER onto them.
Wait a few minutes for the product to act and dissolve the dirt.
Then remove the dirt with a cloth.
Repeat the operation if the dirt is difficult to remove.
It can also be diluted with water to clean delicate surfaces or fabrics.

CHARACTERISTICS
Base: Mixture of detergents and degreasers
Appearance: Transparent amber liquid
Odour: Fragranced
pH: Alkaline
Viscosity: Fluid
Biodegradability: Over 80%

ANTITEK® is a new generation water-based anti-spatter aerosol, harmless to users. Thanks to its composition, silicone-free and with selected raw materials, ANTITEK® allows subsequent and successive surface treatments (painting, galvanizing or chrome treatment)
ANTITEK® is used to prevent the adhesion of impurities or spatter on welded elements or on the wear parts of welding torches.

500 ml aerosol

INSTRUCTIONS FOR USE
Spray around the end of the torch or on the metal to be welded or cut.
Do not spray on welding strips.
Shake before use.
Apply a first burst into the air when the aerosol is new.
Spray at a distance of 25-30 cm from the parts to create a film that will prevent spatter. Do not spray too long, or closer than 25 cm from the part.
Do not spray an excessive amount of product.
Degrease the welded part with detergent products before proceeding with surface treatments.
Use-by date: 10 months from the production date indicated on the aerosol.

CHARACTERISTICS
Base: Synthetic oil mixed with water base. SILICONE-FREE.
Propellant: Mixed, denatured, non-toxic, ecological gas.
Appearance: Clear liquid
Viscosity at 25°C: 20-50 cst
Odor: None
Anti-spatter performance: Very good

Final treatment phase to restore the stainless property of steel

Available in 2 and 10 kg pots in gel form

This brush is used for applying stainless steel cleaning products.
Wooden handle, acid-resistant.

Brush width 30 mm
Handle length 30 cm

ZINCONSIL 430 is used for cold galvanising on all metals. An aerosol with a high zinc content used particularly for touch-ups on welds, to restore or galvanise metal parts, to galvanise and protect bolts exposed to weathering for long periods, to restore grilles, gates, metal parts, containers and metal structures.
ZINCOSIL 430 is also an effective protector against corrosion from atmospheric agents, salt and moisture.

400 ml aerosol

PROPERTIES:
- Contains no chlorinated solvents,
- High zinc content,
- Fast drying,
- Does not drip,
- High coverage power,
- High corrosion resistance,
- Good resistance to atmospheric agents, washing agents, oxidising agents.
- Colour identical to galvanising,
- Durable protection
- The aerosol is fitted with an anti-drip diffuser; its use does not cause stains.

INSTRUCTIONS FOR USE
Shake before use for one minute until the ball inside moves freely.
Even during application, shake the product regularly to keep it homogeneous. Clean and degrease the surfaces to be treated. Spray from a distance of approximately 25 cm.
After use, invert the aerosol and spray the product for a few seconds to prevent the valve from becoming blocked.

SPECIFICATIONS
Base: Pure zinc 98% on synthetic backing
Pigment purity:>98%
Propellant: Denatured and odourless hydrocarbon
Appearance: Light grey colour
Dry film thickness: 20 to 40 µm (cross-coat)
Coverage capacity: high
Coverage rate: approx. 120 ml/m²
Temperature resistance: -50°C to +250°C (Metal powder resists up to 700°C)
Drying time: 5 to 10 minutes. Fast drying, does not drip.
Electrical conductivity: high
Abrasion resistance: Very high
Cross-cut: DIN 53151 - ISO 2409 = GTO/GT1
Oxidation resistance: Very good corrosion resistance

SUPER BALL is the best method for finding a gas leak on pressurized parts. Bubbles appear at the location of the leak. It can be used on all gases, even at low pressure (nitrogen, carbon dioxide, refrigeration systems).
Thanks to its formulation with specially selected components, it reveals micro-leaks on low surface tension surfaces

500 ml aerosol

INSTRUCTIONS FOR USE
Shake the aerosol well before use.
Spray the product from a distance of 10 cm;
For professional use only

CHARACTERISTICS
Base: Mixture of foaming components
Propellant: Denatured and odorless hydrocarbon
Appearance: White foamy liquid
Application temperature: -10°C to +130°C (approximately)
Biodegradability: Greater than 80%
Odor: None
CFC-FREE, non-toxic

Stainless steel weld cleaning liquid for wide or long weld beads
1 L container.
Applied with a suitable pad. Reference 981866

PROTECT 700 is an anti-spatter liquid used to prevent the adhesion of slag or welding spatter.
This product contains no silicone and therefore allows subsequent surface treatments (painting, galvanizing, chromating).
PROTECT 700 can be used in an enclosed space as it is neither flammable nor toxic.
It can be diluted with water in a ratio of 1 to 5; for welding robots, it is recommended to dilute the product with water in a ratio of 1 to 1; for application with a pump, it is possible to use the product pure or diluted 1 to 1.

Base: Synthetic oil, silicone-free.
Appearance: Light yellow
Viscosity at 25°C: 30-100 cSt (Brookfield)
Temperature resistance: from -2°C to +200°C
Biodegradability: over 80%
Dilution: with water in all proportions
pH: 7 to 8
Non-flammable, non-toxic, odorless.

INSTRUCTIONS FOR USE
• Fill a sprayer:
• Spray at 20 cm from the part to be protected
• Deposits a thin, uniform film facilitating the rapid removal of welding spatter
• Remove with a degreaser or cleaner before galvanizing or painting the part(s) that have received SOUDURE ANTI GRATTONS

 It is also possible to apply this anti-spatter product with a brush on the surface to be treated.

Removes oxides after stainless steel welding.

Available in 2 kg and 10 kg tubs in gel form

Pickling is the operation that removes all oxides after welding, by removing the surface depleted as a result of heat treatment.
It is the most important step in the treatment process.
It must be taken into account that a weld bead is a surface that has been heated and generally loses its stainless properties.
For these reasons, the pickling operation does not simply mean cleaning the weld beads but primarily consists of restoring the stainless steel's characteristics.

How to use Picklinox paste?

Degrease the surface to be treated with the specific product CLEANOX.
Then apply a layer of paste.
Rinse with water after a variable time depending on the grade of stainless steel and the type of welding (up to 30 minutes).
Do not expose the product or the treated surface to sunlight or any atmospheric agent.

METACLEAN is a degreaser and aerosol cleaner for metals.
It removes all types of dirt present on metal: oil traces, grease, incrustations, tar, carbon and adhesive residues. It is also effective on steel and aluminum.

400 ml aerosol can

INSTRUCTIONS FOR USE
(Concentrated product – shake well before use)
Spray onto surfaces to be treated, then clean with a cloth or with compressed air.

CHARACTERISTICS
Base: Mixture of solvents and degreasers with low surface tension
Appearance: Clear liquid
Propellant: Denatured hydrocarbon, non-toxic, odorless, colorless.
DOES NOT CONTAIN CFC

3 products for complementary use:

PENETRANT:
Red dye used to highlight small defects that may cause leaks.

DEVELOPER:
White powder product. It is used in conjunction with the PENETRANT and highlights small defects that may cause leaks.
Its white powder draws out by capillary action the red penetrant embedded in the crack from a thickness of 30 microns.
Easy to apply, non-destructive testing.

CLEANER:
Surface cleaner to be used before and after dye penetrant testing.
Penetrates into the smallest cracks and removes excess PENETRANT.

Silicone-free anti-spatter spray for protection of contact tips and gas nozzles.
Volume 400 ml
For use on cold parts, compatible with paint.

Cleaning pad kit for Cleantech 200 Telwin
This item is used when cleaning with the CLEAN IT cleaner
These pads are suitable for cleaning large weld beads

The active ingredient of the SOUDURE ANTI-GRATTONS is effective over time and benefits from high anti-adhesion properties that prevent the adhesion of metal spatter and weld spatters on welding torch nozzles or any surfaces near the work area. Formulated without chlorinated or petroleum solvents, the SOUDURE ANTI-GRATTONS is neither toxic nor irritating.

Thanks to its specific water-based formulation, the SOUDURE ANTI-GRATTONS is non-flammable, releases no unpleasant odour and generates neither smoke nor dangerous vapours for the user during welding operations. The SOUDURE ANTI-GRATTONS is 92% biodegradable.

The SOUDURE ANTI-GRATTONS rinses off very easily with water and contains corrosion inhibitors. Silicone-free, it is compatible with post-finishing operations and can be used on surfaces that are to be painted, bonded or varnished.

The SOUDURE ANTI-GRATTONS is particularly recommended when you want to avoid any trace of grease on metal surfaces. It also facilitates the demoulding of parts made of polyurethane, polyester, epoxy, various plastics or rubber moulded by injection, compression or casting.

SOUDURE ANTI GRATTONS Silicone-free water-based anti-adhesion spray

MAIN CHARACTERISTICS
• Water-based formula without chlorinated or petroleum solvents
• Prevents the adhesion of molten metal spatter: welding spatter.
• Non-flammable
• Easy removal of welding spatter by simple brushing
• Transparent film in the form of micro-droplets
• Long-lasting protection
• Releases no vapour or smoke
• No unpleasant odour • Mould release action
• Contains a corrosion inhibitor
• Very easy removal of the SOUDURE ANTI GRATTONS film
• Silicone-free to facilitate post-finishing operations

FIELDS OF APPLICATION
• Protection of the welding station environment
• Protection of parts before welding
• Nozzle, soldering iron tip
• Welding robots
• Steel or aluminium moulds • Mould release agent for plastic injection moulding

PENTRIX 100 is a red penetrant liquid in aerosol form, formulated to reveal cracks, crazes or porosity caused by welding on ferrous materials and other metals.
Thanks to its intense colour and composition, PENTRIX can penetrate the most complex areas and reveal cracks and crazes caused by welding.

400 ml aerosol

INSTRUCTIONS FOR USE
Shake well before use.
1. Degrease and clean the surface to be treated with METACLEAN aerosol degreaser;
2. Spray PENTRIX 100 on the parts to be inspected;
3. Wait 10 to 70 minutes for the product to fully penetrate.
4. Clean the treated surfaces with water or solvent. Do not spray solvent aerosol directly onto treated surfaces as this could remove all of the red liquid.

CHARACTERISTICS
Base: Mixture of petroleum distillates, dyes and surface tension protectors.
Appearance: Red liquid
Propellant: Denatured hydrocarbon, non-toxic and odourless
CFC-FREE